Geotab GO Focus Plus Technical Information: Lights, Specs and Manual

How Do You Read the GO Focus Plus Dash Camera Status Light?

The GO Focus Plus reports its condition through a single status light. Geotab says it has three statuses but prints that table only as a picture. Two patterns are written out in Geotab's text, blinking blue at power-up and solid green when ready, and those are the two we show. Tap any button below to see it and hear what it means.

🔇 The GO Focus Plus has no status sounds. Watch the light.

Easy way to remember it: Blue, booting. Green, good to go.

Tap a button to see it

Each button plays the pattern on the GO Focus Plus above, says out loud what it means, and tells you what to do.

What Does Each GO Focus Plus Light Mean?

Light	Meaning	What to do
Blue, blinking	Powering up after the dash cam and vehicle are switched on	Leave it connected and wait
Green, solid	Ready; on a first power-up this arrives after about 4 to 5 minutes	Nothing; carry on with aiming and checks

Geotab shows the third status only as a picture, so we leave it out rather than guess; our technicians read any other pattern against Geotab's guide on site. The loudspeaker is for spoken driver alerts, not status codes.

What Does a Normal Install Look Like, Minute by Minute?

Cable first. The Smart Cable's power plug goes into the dash cam's power port, and its other end goes into the IOX port under the GO device's port cover.
GO device in. The GO device plugs into the vehicle's diagnostic port or harness, usually in the driver footwell.
Power on. With the vehicle on, the status light starts blinking blue.
4 to 5 minutes. On a first power-up, the light should settle to solid green. The animation compresses this wait.
Aiming. In the Geotab Video app, the driver's face goes inside the blue rectangle and the horizon between two blue lines.
Sign-off. MyInstall checks the status; on a fail, cycle the ignition and press Refresh.

How Do You Use the GO Focus Plus Day to Day?

Once aimed, the GO Focus Plus coaches drivers in the cab. When it spots distraction, fatigue or tailgating it speaks up right then, and serious events rise to a manager in MyGeotab, riskiest first. Coaching is assigned and tracked there, and event video is kept 365 days by default.

For drivers the routine is short: badge in on the built-in NFC and RFID reader if the fleet uses it, keep the lenses clear, and treat a voice alert as a nudge. A light that is not solid green while driving is worth reporting.

Which Harness and Connection Parts Go With the GO Focus Plus?

The GO Focus Plus Smart Cable is the one required part. It is 3 m long and connects the dash cam to the IOX port on a GO9 or newer device. An IOX extension cable can lengthen it, but the total run is capped at 5 m. Geotab's rules for that chain:

Last in line. The dash cam must be the final device in the IOX chain.
Current budget. It draws 1 A at 12 V from the IOX bus, leaving 1.5 A for other IOX add-ons.
GO9 RUGGED. A GO9 RUGGED needs a 6-way IOX harness, and that setup takes no other IOX add-ons.

The GO9 itself stays on its usual T-harness, such as the HRN-GS16K2-LD or HRN-GS09K2-A.

The GO Focus Plus closes off the IOX chain, inside a 5 m total run and a 1 A share of the bus.

What Are the GO Focus Plus Technical Specifications?

Item	Value
Lenses	1080p road lens; 720p cabin lens with 940 nm infrared
Status indicator	One status light; blue and green patterns written out in Geotab text
Audio	Loudspeaker for voice alerts; noise-cancelling microphone that can be disabled
Power	12 V and 24 V; 6 W nominal (0.5 A at 12 V)
Parking and deep sleep	30 mA and 7 mA at 12 V
IOX bus draw	1 A at 12 V through the Smart Cable
Size	Dual: 123 x 106 x 45 mm. Road-Only: 98 x 106 x 45 mm
Cellular and wireless	LTE Cat 6; Wi-Fi 5; Bluetooth 4.2 with BLE
Storage	128 GB microSDXC included; 512 GB and 1 TB options
Operating temperature	-20 to +60 °C
Compatible GO devices	GO9 and GO9 RUGGED

What Should Installers Check Before Leaving a GO Focus Plus?

Leave only once the light is steady green. Confirm the dash cam is the last link in the IOX chain and the run stays within 5 m. Recheck both aims with the driver seated normally. Make sure MyInstall shows a pass with the dash cam recorded.

What Are Common Questions About the GO Focus Plus's Lights and Setup?

What is the easiest way to remember the GO Focus Plus light?

Blue, booting. Green, good to go. Blinking blue means the dash cam is still powering up, and solid green means it is ready, which on a first power-up takes about 4 to 5 minutes.

Why do we hear beeps during a GO Focus Plus install?

Those beeps come from the GO9 it plugs into, not the dash cam. Geotab's guide describes two quick beeps every 60 seconds while the GO device sets up and ten quick beeps once its three lights go solid.

What if the light never turns solid green?

Give it the full 4 to 5 minutes on a first power-up. If it still is not green, our technicians check the Smart Cable at both ends, the IOX chain order and the GO device before anything is replaced.

When a GO Focus Plus won't reach green, or its aim has drifted, our technicians bring the fix to your yard and re-aim both lenses with the driver seated. Phone 803-513-1009, or start with Get a Quote.

Sources: GO Focus Plus quick start guide, GO Focus Plus install guide (status light, aiming), GO Focus Plus install guide (verification), GO Focus Plus and GO device, GO Focus Plus technical specifications. The animation is our illustration of Geotab's published patterns; flash speeds are approximate because Geotab does not publish exact timings. GEOTAB is a registered trademark of Geotab Inc. API Signal is an independent installer and is not Geotab.

Every Geotab Product →Trackers, cameras, asset trackers and IOX add-ons. Get a Quote →The GO Focus Plus supplied and installed on one written quote.

Geotab GO Focus Plus Technical Information