Geotab SPR-NFCBRACKET Harness

← All Geotab harnesses

What Is the SPR-NFCBRACKET?

The SPR-NFCBRACKET is a replacement mounting bracket and holder for Geotab's IOX-NFCREADER, the near-field reader drivers tap with a tag or card to log in to a vehicle. Geotab packages it with two screws and double-sided tape, and describes its role as giving installers a replacement bracket for the NFC reader.

The reader already ships with a bracket. This part exists for when that bracket is broken, lost during a vehicle swap, or left behind when the reader is moved to a new unit. A cracked or missing holder is a common reason readers end up loose on the dash, and a loose reader gets knocked, unplugged or ignored.

Geotab's harness document says very little about the bracket itself, so the practical guidance on this page draws on Geotab's IOX-NFCREADER installation documentation.

Which Vehicles and Devices Does the SPR-NFCBRACKET Work With?

Geotab lists the bracket for the IOX-NFCREADER. The reader connects to the GO device's IOX expansion port through a 90 degree USB connector, and Geotab states driver identification works with all GO7 and newer devices and variants, while keyless use needs a GO9 or newer. The bracket itself is a mechanical part and fits wherever the reader would be mounted in a car, van, pickup or truck cab.

For keyless installs on the windshield, Geotab uses a different optional window mount, the SPR-NFCBRKTV2ASY, which comes with dual-lock tape. The SPR-NFCBRACKET is the screw-down holder, so it belongs on the dash or a trim surface.

What Problem Does It Solve on the Job?

Driver ID only works if drivers can reach the reader and actually use it. When a holder breaks, the reader tends to get stuffed into a cup holder or left swinging on its cable, and tap rates fall. Managers then see trips with no driver attached, which undermines safety scoring, hours reporting and any coaching program built on who was behind the wheel.

A replacement bracket puts the reader back where it belongs, at a fixed point every driver knows. It is also the part we reach for when a fleet moves readers between vehicles during replacements, because the original bracket is usually screwed down and does not come out cleanly.

How Is the SPR-NFCBRACKET Installed?

Geotab's bracket entry says to use the screws or double-sided tape to fix it to the vehicle. Its reader documentation adds detail, which we follow:

• Do not work on the vehicle while it is running or moving. Unplug the GO device and remove the IOX port cover if the reader is being reconnected.
• Pick a location the driver can reach that does not block the view, interfere with airbags or affect safe operation, and confirm the reader cable will reach before fixing anything.
• Use the tape to hold the bracket in place, then drive the screws; Geotab says the tape alone is not a permanent mount.
• Seat the reader in the holder and route the cable with cable ties, avoiding tight bends.
• Reconnect the reader's USB plug to the GO device and tie it without overtightening, then secure the GO device with two cable ties.
• Plug in the GO device and start the vehicle, tap a valid tag to test, and confirm a pass on MyInstall.

Which Related Harnesses Should You Compare?

• SPR-INSTALLBAG: bracket and hardware for mounting the GO device itself.
• SPR-RELAYKIT: Driver ID relay kit that works alongside the reader and needs professional fitting.
• HRN-IOXEXT-A: 2 m IOX extension for when the reader's position is far from the GO device.

What Are Common Questions About the SPR-NFCBRACKET?

What is included with the SPR-NFCBRACKET?

Geotab lists a mounting bracket and holder for the IOX-NFCREADER, along with a pair of screws and a piece of double-sided tape. The reader itself is not included.

Can the bracket be mounted with tape alone?

Geotab's NFC reader documentation says the supplied tape only holds the bracket in position during installation and is not a permanent mount; screws must be used to finish the job.

How does a driver know the tag was read?

In driver identification use, Geotab says the reader's green LED flashes twice and the GO device gives a single beep when a valid tag is read. If nothing happens, we check the tag, the mount position and the IOX connection.

API Signal supplies and installs Geotab harnesses and devices on site at the customer's yard, including driver ID readers and their brackets. Call 803-513-1009 or use Get a Quote to set up driver identification across your vehicles.

Sources: Geotab Harness Identification and Application, Geotab IOX-NFCREADERA support document. GEOTAB is a registered trademark of Geotab Inc. API Signal is an independent installer and is not Geotab.