Mastering Geotab
★ Geotab Products · Technical Information
The GO Focus Pro shows its status through one light: cyan while it starts, green when it works, red for weak signal and a slow blue blink when parked. This page plays each pattern and collects the wiring, setup and spec details.
The GO Focus Pro reports on itself through a single status light with four published patterns. Two steady colors tell you whether it is starting or working, a flashing red warns of weak coverage, and a slow blue flash means it is asleep. Tap any button below to see it and hear what it means.
🔇 The GO Focus Pro has no status sound. Watch the light.
Easy way to remember it: Cyan, coming up. Green, working. Red, no signal. Slow blue, asleep.
Tap a button to see it
Each button plays the pattern on the GO Focus Pro above, says out loud what it means, and tells you what to do.
| Light | Meaning | What to do |
|---|---|---|
| Cyan, solid | Initializing or waking up | Leave it powered until it finishes |
| Red, flashing | Weak or no cellular signal | Move the vehicle somewhere with better coverage |
| Green, solid | On and working | Nothing; this is normal |
| Blue, slow flash | Parking mode or sleep | Nothing; drive the vehicle to bring it online |
Those four rows are Geotab's full published list. The Pro has a loudspeaker for collision and driver alerts, but Geotab documents no start-up or status sound, so the light is the only status signal.
In service, the GO Focus Pro wakes with the vehicle, passes through cyan and holds green while it records the road and cabin. It warns the driver of collision risk ahead, recognizes traffic lights and plates, and with side units added watches blind spots. Managers review events and live video in MyGeotab. Once parked, it drops to a slow blue flash.
The habits that keep it healthy are simple. Use only Geotab's SD cards, since the Pro supports no others. Keep the sun visor and mirror clear of the cabin lens. Flashing red that lasts beyond a poor-coverage area is worth reporting.
Unlike the smaller Focus models, the Pro takes power straight from the vehicle through the HRN-IOXGFPRO-3W 3-wire harness, which is sold separately:
A separate IOX harness links the dash cam to a GO9 or newer GO device so the two pair automatically. Geotab warns against routing the cable under the headliner where roof airbags are fitted; the run then follows the A-pillar trim and door weatherstrip instead.
| Item | Value |
|---|---|
| Status indicator | One status light: cyan, green, red and blue patterns |
| Audio | Loudspeaker; noise-cancelling microphone |
| Power | 12 V and 24 V; 6 W nominal (0.5 A at 12 V) |
| Parking and deep sleep | 50 mA and 7 mA at 12 V |
| Power harness | HRN-IOXGFPRO-3W, sold separately |
| Size and weight | Dual: 124 x 88.6 x 101 mm, 340 g. Road-Only: 124 x 88.6 x 72 mm, 300 g |
| Cellular and location | LTE Cat 4 with data plan; GPS, QZSS, GLONASS and Galileo |
| Storage | 128 GB included; 512 GB and 1 TB options; two slots, 2 TB total; Geotab cards only |
| Temperature | -20 to +60 °C operating (+70 °C in some conditions); -30 to +85 °C storage |
| Ingress rating | IP30 (main unit) |
Prove the yellow wire sits on a slot that stays live with the key off and the red wire on one that drops with it. The light should go from cyan to solid green within the published 4 to 5 minutes. Lower the sun visor fully and confirm it clears the cabin lens. Keep the cable clear of roof airbags, tie everything behind the fuse panel, and confirm the report saved in the History tab.
Cyan, coming up. Green, working. Red, no signal. Slow blue, asleep. Cyan means it is starting or waking, green means all is well, flashing red means weak cellular coverage and a slow blue flash means parking mode.
A slow blue flash is parking mode, the dash cam's sleep state, and Geotab lists no action for it. Driving the vehicle brings it back online, and the light passes through cyan to green.
Geotab's guide says that on the rare vehicle without an ACC interface, the red wire goes to ground instead. Our technicians confirm that with a multimeter before making the connection.
If a GO Focus Pro won't leave cyan, keeps flashing red in good coverage or never sleeps, our technicians trace the fuse taps, ground and IOX link on site. Ring 803-513-1009 or open Get a Quote.
Sources: GO Focus Pro quick start guide (LED table, wiring), GO Focus Pro install guide, GO Focus Pro technical specifications. The animation is our illustration of Geotab's published patterns; flash speeds are approximate because Geotab does not publish exact timings. GEOTAB is a registered trademark of Geotab Inc. API Signal is an independent installer and is not Geotab.
Tell us how many vehicles and what they are. We'll quote the hardware and the install together.