Help build this pageWant to be famous?Share a wire color, a photo or a tip for this truck, and your name goes on this page.
Add yoursClose▾
Which wires give constant, ignition and ground on a 2010 Chevrolet Impala?
On a 2010 Chevrolet Impala, take constant power from the Red/White wire at the ignition switch harness, ignition from the Pink wire at the ignition switch harness, 6-pin plug, pin 3, and ground to clean, bare body metal. Meter every wire first.
Written by API Signal, fleet GPS and camera installers for 35+ years across Georgia, South Carolina and North Carolina, installing every major telematics and camera brand. Every wire on this page lists its source.
Test every wire with a meter before you tap it
No wiring information is ever guaranteed. Colors and locations change with trim, options and build date, and the manufacturer can change them in the middle of a model year. We share this as a starting point for installers, and you are responsible for confirming every connection on the truck in front of you.
This page covers the 2010 Chevrolet Impala.
This car has a standard key. The colors come from one wire sheet that covers 2009 to 2013. Our own team has not yet metered these on this car.
OBD-II portLocation not confirmed
Best power spotIgnition switch harness
System voltage12V
Ignition typeKey
Need More Installs?
We send fleet installation work to independent installers. One job goes to one installer. Now adding network partners in North Carolina.
Each chip shows the main insulation color with its stripe. Source: a 2009 to 2013 Impala wire sheet on the12volt.
Where are the brake, door, speed and CAN wires on a 2010 Chevrolet Impala?
Circuit
Wire color
Location and what it does
BrakePositive +Not yet checked
Light Blue
BCM left of the steering column, brown plug, pin 5Hot with the pedal pressed.
DoorsNegative -Not yet checked
Tan
BCM, gray plug, pin 23One wire for all doors; grounds with any door open.
Parking brakeNot foundNot yet checked
Not found
Not foundNot on the 2009 to 2013 sheet. On 2006 and 2007 cars it is Orange/Black at the BCM pink plug, pin 22, so meter that pin.
HazardNot foundNot yet checked
Not found
Not foundNot on the 2009 to 2013 sheet.
Lock / unlockNegative -Not yet checked
Pink/Black (lock)
Orange/Black (unlock)
BCM, gray plug, pins 12 and 11Lock and unlock inputs.
Trunk releaseNegative -Not yet checked
Light Blue
BCM, white plug, pin 10Grounds to release the trunk.
SeatbeltNot foundNot yet checked
Not found
Not foundWe found no source for this wire.
Vehicle speedAC signalNot yet checked
Brown
ABS module at the left front strut towerReported for 2010 and 2011 cars.
TachAC signalNot yet checked
Any uncommon wire at one injector
Fuel injectors in the engine bayUse the wire that differs from injector to injector, not the shared feed.
CAN busNot foundNot yet checked
Not found
Not foundNo source gave the data wire colors or pins for this car.
Sources: a 2009 to 2013 Impala wire sheet on the12volt and owner posts for the speed wire (installer-reported). Turn signals, headlight, reverse, hazard, parking brake, seatbelt and the data bus wires were not found.
Which years share wiring with the 2010 Chevrolet Impala?
This page2010Covered by the 2009 to 2013 wire sheet.
Same wiring2009, 2011, 2012 and 2013One wire sheet covers 2009 to 2013. The engine changed for 2012, and the speed wire moved with it.
Where are the fuse boxes and ground points on a 2010 Chevrolet Impala?
InteriorFront passenger footwell, behind a coverAuxiliary outlets fuse F7 (20A), retained accessory power F3 (10A).
Under the hoodRight side of the engine bayAuxiliary power fuse (25A) and BCM fuse (10A).
Ground pointsClean body metalNo named ground point found. Never use the battery negative post.
Fuse list from fuse guides for 2006 to 2013. Check the lid label before you use a slot.
Where is the OBD-II port on a 2010 Chevrolet Impala?
OBD II
Diagnostic portOBD-II port: location not confirmedLook under the driver side dash first, and send us a photo if you find it.
Common questions about 2010 Chevrolet Impala wiring
What wire is constant power on a 2010 Chevrolet Impala?
Red/White at the ignition switch harness. Always hot. Meter it before you tap it.
What wire is ignition on a 2010 Chevrolet Impala?
Pink at the ignition switch harness, 6-pin plug, pin 3. Hot in run. Meter it before you tap it.
Where is the brake wire on a 2010 Chevrolet Impala?
Light Blue (positive +) at the BCM left of the steering column, brown plug, pin 5. Hot with the pedal pressed. Meter it before you tap it.
Where is the vehicle speed signal on a 2010 Chevrolet Impala?
Brown at the ABS module at the left front strut tower. Reported for 2010 and 2011 cars. Meter it before you tap it.
Which years share wiring with the 2010 Chevrolet Impala?
2009, 2011, 2012 and 2013. One wire sheet covers 2009 to 2013.
Help build this page
Had the panels off on one of these? Show the next installer what you found.
No one has sent photos for the 2010 Chevrolet Impala yet, so yours could be the first. Every photo, wire color and tip we use goes on this page with your name on it, and it saves the next installer time under the dash.
1. Snap it
The plugs, tap points, fuse boxes and ground points. Phone photos are fine.
2. Send it
Tap "Add yours" at the top of this page. Your tip and your photos go in the same box.
3. See your name on it
We check every tip, then post it here "Compliments of" you, by name.
Compliments of
The installers who helped build this page.
★
Founding contributor spot: openThe first installer to confirm a wire or send photos for the 2010 Chevrolet Impala gets their name here, and it stays here.
★
Every tip we use gets a creditThe wire you checked is marked "Checked on a truck, compliments of" you.
Want to be famous?
Your name, right on this page, for everyone who uses it to see. Add your tip and your photos in one box.
